6.3.9 SemiBlindICA

6.3.9.1 Overview

This module removes a known signal (e.g., the utterance from a spoken dialogue system) from the multichannel observed mixture. The algorithm presented in Reference $^(1)$ is implemented in this module.

6.3.9.2 Necessary files

N/A.

6.3.9.3 Usage

When to use Here is an example in the context of a spoken dialogue system. When a spoken dialogue system dispenses with a close-talk microphone, the microphone may capture the mixture of the utterance of the user of the system and the utterance from the system itself because the microphone is located in a distance from the mouth of the user. In this situation, the speech recognition quality is degraded because the input signal captured by the system contains both the target voice of the user and interfering system utterance.

Generally speaking, when the multichannel observed signal recorded by a microphone array contains a known signal component, we can remove the known signal component from the observed mixture signal. In the example above, the system utterance corresponds to the known signal component. Here, a “known” signal means that we know the waveform of the signal when it is played. For example, when we have a wav file to play with a loudspeaker, the signal is known. Usually, the waveform of an observed signal by a microphone is usually different from the waveform that was played from a loudspeaker. This is because the spatial propagation of the sound changes the waveform and adds some reverberation. Besides, there is some time difference of arrival due to the distance between the sound source (e.g., a loudspeaker) and receivers (e.g., microphones). Since SemiBlindICA module explicitly models this propagation of the known sounds, the original waveform being played is sufficient information to remove the known signal component.

Typical connection Figures 6.62 and 6.63 show the typical usage of SemiBlindICA node. In Figure 6.62, the multichannel observed mixture including the known and unknown signal components is connected to INPUT. The known component is connected to REFERENCE terminal. These signals are converted into the time-frequency domain with MultiFFT node. From OUTPUT terminal, the unknown signal component is produced where the REFERENCE is removed from INPUT. This OUTPUT can be connected to LocalizeMUSIC node for further analysis of the unknown component.

Figure 6.63 illustrates an example that uses a stereo wav file. In the wav file, the first (left) channel contains the known signal component while the second (right) channel contains the mixture of known and unknown components. ChannelSelector node is used to extract each channel from a multichannel wav file. In Figure 6.63, the separated unknown signal component is finally saved as another wav file using SaveWavePCM node.

6.3.9.4 Input-output and property of the node

Input

INPUT

: Matrix<complex<float> > type. Multichannel observation that contains both known and unkonwn signal components. This is complex-valued spectra obtained by MultiFFT node.

REFERENCE

: Matrix<complex<float> > type. Complex-valued spectra of the known signal component.

Output

OUTPUT

: Matrix<complex<float> > type. The output signal is generated by suppressing the known signal REFERENCE from the observed mixture INPUT. This is in the same multichannel format as INPUT terminal.

Parameter

CHANNEL

Number of channels of the input mixture INPUT.

LENGTH

Windows length of the short-time Fourier transform. HARK uses 512 [pt] by default.

INTERVAL

This parameter adjusts the length of the filter to remove the known signal component depending on the step size of the short-time Fourier transform. This multirate repeating is introduced to improve the convergence of the filter learning$^{(2)}$. This value is denoted by $K$ in the math expressions below.

TAP_LOWFREQ

The length of the filter at 0 [Hz]. The length of the filter accounts for the time difference between the REFERENCE signal and the known component in INPUT, and the reverberation in the observed signal. When the environment contains a long reverberation, this value is set larger accordingly. This value is denoted by $M_ L$.

TAP_HIGHFREQ

The length of the filter at the Nyquist frequency. The filter length at each frequency bin is determined by the linear interpolation of TAP_LOWFREQ and TAP_HIGHFREQ. This value is denoted by $M_ H$.

DECAY

The decaying parameter for the learning rate of each element of the filter to remove the known signal component. In a reverberant environment, such as an indoor situation, the filter element corresponding to the past time frame exponentially decays. Since the filter element values follow an exponential curve, the learning of the filter values becomes efficient when the learning rate for each filter value is also set exponentially decaying values. When this value is set $1$, the learning rate becomes identical for all filter values. We empirically set this value at 0.6–0.8. This value is denoted by \lambda.

MU_FILTER

The filter values are obtained though the stochastic gradient method. This is the learning rate for the learning procedure. Generally speaking, a large learning rate is able to drastically update the parameters while there is a risk of the fluctuation of the parameters around the (local) optimum value. On the other hand, a small learning rate can avoid the risk of the fluctuation, while the number of parameter updates may increase before convergence. This is denoted by $\mu _ w$.

MU_REFERENCE

Learning rate for the normalization parameter of the known signal component. The normalization of the known signal is carried out to accelerate the learning. This value is denoted by $\mu _{\alpha }$.

MU_UNKNOWNSIGNAL

Learning rate for the normalization parameter of the unknown signal component. Similarly to MU_REFERENCE, this normalization is introduced for an efficient learning. This is denoted by $\mu _{\beta }$.

IS_ZERO

To save the computational resource, the filter update procedure is omitted if the INPUT contains no signal. This is the threshold to detect the existence of a signal. When the power of the INPUT is below this value, this time frame is ignored. Note that this threshold is applied to the power of the signal in the time-frequency domain, instead of the waveform in the time domain.

FILE_FILTER_IN

File name (path) that contains the initial filter values. If “-null” is specified, no file is used for the initialization.

FILE_FILTER_OUT

File name (path) to write out the filter values. If “-null” is specified, no file is written out.

OUTPUT_FREQ

The interval in terms of time frame to save the filter values.

6.3.9.5 Detail of the node

SemiBlindICA node suppresses the known signal component from the multichannel observation that contains both the known and unknown signals using independent component analysis (ICA). The ICA algorithm is derived based on the mixing process in the time-frequency domain and the statistical independence between the known and unknown signals.

Mixing model and the separation process: SemiBlindICA node uses the following mixing process in a reverberant environment. This model is a linear mixing process in the time-frequency domain. Let $\omega $ be the frequency bin index, $f$ be the time frame index, and $X(\omega , f)$ be the observed signal at frequency $\omega $ and time $f$. The observation is modeled as

$\displaystyle X(\omega , f) = N(\omega , f) + \sum ^ M_{m=0} H(\omega , m)S(\omega , f-m), \nonumber $

where $N(\omega , f)$, $S(\omega ,f)$, and $H(\omega ,m)$ denote the unknown signal, the known signal, and the propagation coefficient with a time lag of $m$ frames.

The separation process is derived as follows using ICA.

	$\displaystyle \left( \begin{array}{c} \hat{N}(\omega , f) \\ {\boldsymbol S}(\omega , f) \end{array} \right) $	$\displaystyle = $	$\displaystyle \left( \begin{array}{cc} a(\omega ) & -{\boldsymbol w}^ T(\omega ) \\ {\boldsymbol 0} & {\boldsymbol I} \end{array} \right) \left( \begin{array}{c} X(\omega , f) \\ {\boldsymbol S}(\omega , f) \end{array} \right), \label{eq:unmix} $		(101)
	$\displaystyle {\boldsymbol S}(\omega , f) $	$\displaystyle = $	$\displaystyle [S(\omega , f), S(\omega , f-K), \cdots , S(\omega , f-M(\omega )K)]^ T, \nonumber $
	$\displaystyle {\boldsymbol w}(\omega ) $	$\displaystyle = $	$\displaystyle [w_0(\omega ), w_1(\omega ), \cdots , w_{M(\omega )}(\omega )]^ T, \nonumber $
	$\displaystyle M(\omega ) $	$\displaystyle = $	$\displaystyle {\rm floor}\left(\omega / \omega _{nyq}(M_ U - M_ L)\right) + M_ L. \nonumber $

Here, $\omega _{nyq}$ denotes the maximum value of the frequency bin index (corresponding to the Nyquist frequency). The separation filter ${\boldsymbol w}(\omega )^ T$ is a $M(\omega )+1$-dimensional filter, where ${\boldsymbol w}^ T$ is the transpose of vector ${\boldsymbol w}$. $K$ is the factor for multirate repeating$^(2)$ introduced for an efficient convergence of the filter.

Estimation of the separation filter: The separation filter is estimated through ICA processing: the filter is obtained by minimizing the Kullback-Leibler divergence (KLD) between the product of the probability density function of $\hat{N}$ and ${\boldsymbol S}$, and the joint distribution of these variables. The update procedure is derived by using the nonholonomic constraint$^(3)$ and natural gradient method. Let ${\hat N}_ n$ be the normalized unknown signal. The separation filter to suppress the known signal component is incrementally updated as follows.

	$\displaystyle {\boldsymbol w}(\omega , f+1) $	$\displaystyle = $	$\displaystyle {\boldsymbol w}(\omega , f) + {\boldsymbol \mu }_ w \Phi _{\hat{N}_ n(\omega )}\left( \hat{N}_ n(\omega , f)\right) \bar{\boldsymbol S}_ n(\omega , f), \nonumber $
	$\displaystyle a(\omega ) $	$\displaystyle = $	$\displaystyle 1, \nonumber $

where $\hat{x}$ denotes the complex conjugate of $x$. Here, the higher-order correlation is defined as $\Phi _ x(x) = \tanh (|x|)e^{j\theta (x)}$. ${\boldsymbol \mu }_ w$ is defined as follows.

$\displaystyle {\boldsymbol \mu }_ w = {\rm diag}\left(\mu _ w, \mu _ w \lambda ^{-1}, \cdots , \mu _ w \lambda ^{-M(\omega )}\right). \label{eq:update_ w} $

(102)

This element-wise learning rate has an exponential decay so as to accelerate the learning of the separation filter. From Eq. (101), the unknown signal component $\hat{N}$ is obtained as follows.

$\displaystyle \hat{N}(\omega , f) $

$\displaystyle = $

$\displaystyle X(\omega , f) - {\boldsymbol w}(\omega , f)^ T {\boldsymbol S}_ n(\omega , f). \label{eq:calc_ n} $

(103)

To satisfy the nonholonomic constraint, $\hat{N}$ should be normalized. This is because the constraint requires $E[1-\Phi _ x(x\alpha _ x)\bar{x}\bar{\alpha }_ x] =1$. In the general framework of minimization of KLD based on natural gradient method, variable $x$ has a normalization factor $\nu _ x$ that is incrementally updated as follows:

$\displaystyle \nu _ x(f+1) = \nu _ x(f) + \mu _ x[1 - \Phi _ x(x(f)\nu _ x(f))\bar{x}(f)\bar{\nu }_ x(f)]\nu _ x(f) \nonumber $

This is applied to the normalization of the estimated unknown signal component $\hat{N}$ using the factor $\alpha $ as

	$\displaystyle \hat{N}_ n(f) $	$\displaystyle = $	$\displaystyle \alpha (f)\hat{N}(f), \label{eq:calc_ nn} $		(104)
	$\displaystyle \alpha (f+1) $	$\displaystyle = $	$\displaystyle \alpha (f) + \mu _\alpha [1 - \Phi _{\hat{N}_ n}(\hat{N}_ n(f))\bar{\hat{N}}_ n(f)]\alpha (f). \label{eq:update_ a} $		(105)

For an efficient convergence of the separation filter, SemiBlindICA node normalizes the observation signal using normalization factor $\beta $. Similarly to the case of $\hat{N}$, these quantities are updated as

	$\displaystyle S_ n(f) $	$\displaystyle = $	$\displaystyle \beta (f)S(f), \label{eq:calc_ sn} $		(106)
	$\displaystyle \beta (f+1) $	$\displaystyle = $	$\displaystyle \beta (f) + \mu _\beta [1 - \Phi _{S_ n}(S_ n(f))\bar{S}_ n(f)]\beta (f), \label{eq:update_ b} $		(107)
	$\displaystyle {\boldsymbol S}_ n(f) $	$\displaystyle = $	$\displaystyle [S_ n(f), S_ n(f-K), \cdots , S_ n(f-MK)]. \nonumber $

Flow: The main algorithm of SemiBlindICA node consists of Eqs. (–) for each frequency bin $\omega $ and time frame $f$. Algorithm 6.1 summarizes the core procedures at a certain frequency bin and a channel.

At frequency $\omega $ and frame $f$, the following procedures are carried out.

Calculate $\hat{N}(\omega , f)$ by Eq. ().

Normalize $\hat{N}(\omega , f)$ and ${\boldsymbol S}(\omega , f)$ by Eqs. (, )

Update the separation filter ${\boldsymbol w}(\omega , f)$ using Eq. ()

Update the normalization factors $\alpha (\omega , f)$ and $\beta (\omega , f)$ using Eq. (, )

Output $\hat{N}(\omega , f)$

Algorithm 6.2 presents the overall procedures applied to all the frequency bins and channels. Every time a new time frame is observed, Algorithm 6.1 is applied to each channel and frequency bin.

The following procedures are carried out with a new observation of a time frame.

$f \leftarrow f + 1$

for $ch$ in $0, \cdots , C$ do {default}

for $\omega $ in $0, \cdots , \omega _{nqt}$ do {default}

Run Algorithm 6.1 for $\omega , ch$.

end for

end for

6.3.9.6 Reference

• R. Takeda et al., “Barge-in-able Robot Audition Based on ICA and Missing Feature Theory,” in Proc. of IROS, pp. 1718–1723, 2008.

• H. Kiya et al., “Improvement of convergence speed for subband adaptive digital filter using the multirate repeating method,” Electronics and Communications in Japan, Part III, Vol. 78, no. 10, pp. 37–45, 1995.

• C. Choi et al., “Natural gradient learning with nonholonomic constraint for blind deconvolution of multiple channels,” in Proc. of Int’l Workshop on ICA and BBS, pp. 371–376